PDA350I is a complete solution dedicated to 2-way self-powered loudspeakers. Designed  to  meet  different  applications, it provides 2 channels, composed of one way for powering the Woofer (Low Freq.) and one for powering the Tweeter (High Freq.), with output power of  300W @ 4ohm or150W @ 8ohm(CH1)  + 50W(CH2) @8ohm.  In addition it offers a full set of value adding features such as on board DSP.  To guarantee maximum reliability,  the PDA350I includes  a highly efficient switch mode power supply which provides power to the 2 output channels. The woofer output stage uses the Class D amplifier module - full bandwith PWM modulator obtaining ultra low distortion, high dynamic range and also equipped with a full set of circuit  protections, the Tweeter output stage, is instead powered by a Linear 50W Amp. 

The PDA350I includes a set of sophisticated processes for loudspeaker, implemented by the powerful MARANI® DSP running 96kHz/24bit [96 bits precision for the internal intermediate processes]. Processes as Noise Gate, crossover filters, parametric EQs per input and output sections, RMS compressor, alignment delay and All-Pass filters are available, all in all everything needed to optimize a self-powered loudspeaker. Morever the Clip/Limiter function per channel provides output monitoring to prevent speaker damage with gentle gain reduction at clip threshold, in addition to the efficient heat dissipation system and  Over-Heat  protection  which  themselves  ensure uncompromised reliability.

Furthermore the PDA350I is also equipped with a Dynamic Boost Filter. All setup parameters for input mixing, DSP features and the limiter setting are accessible by using the remote PC software.

Outstanding Performance
High power output: 150W(CH1)+50W(CH2) @ 8ohms; 300W(CH1) @ 4ohms
Switched-Mode Power Supply with auto voltage sensing
Class D Amp Module - full bandwith PWM modulator with ultra low distortion
Full  protection  circuitry  including  Over-Current, Over/Under-Voltage,  Output  DC  and  Over-Temperature
Excellent sonic performance with 24bit high end converters coupled with 96kHz sample rate

 
Top-grade DSP Engine
3 band equalization on input channel 1st Lo-Shelv, 2nd Bell, 3th Hi-Shelving
5 band parametric equalization on output channel
On Low Band the 1st PEQ  can be switched to Bell, Low Shelving
On High Band the 5th PEQ  can be switched to Bell, High Shelving
Input  High-Pass filter up to -12dB/Octave
Crossover filters with slopes from 6dB/Octave up to 24dB/Octave including  Butterworth, Bessel, Linkwitz-Riley
Output channel features a precision dynamic range controller
Adjustable Delay time up to 7 ms for input and 2 ms for woofer output.
Input channel includes a Noise Gate function
Dynamic Boost Filter function
Output Peak Limiter 

 
Control
Simultaneous control up to 32 units via PC software
8 Preset Selection by using rotary encoder switch
Security Lockout

Power & Amplifier section

Number of Channels	2(CH1=Woofer; CH2=Tweeter)
Max Output Power @ 8 ohms	150W(CH1) @ 1%; 50W(CH2) @ 2%
Max Output Power @ 4 ohms	300W(CH1) @ 1%;
Output Circuitry	CH1: Class D - full bandwith PWM modulator with ultra low distortion CH2: Class AB
Output Voltage	48.6 Vp / 97 Vpp (unload)
THD @ Rated power 4Ω (1kHz)	<0.005% (CH1)
THD @ Rated power 8Ω (1kHz)	<0.01%(CH2)
Signal To Noise Ratio	>120 dB (A-weighted, 20 Hz - 20 kHz, 8Ω load)
Frequency Response	20 Hz - 20 kHz ± 0,15 dB (8Ω load, 1 dB below rated power)
Damping Factor	>1000 (8Ω load, 1kHz and below)
Power Supplies	Universal & regulated switch mode power supply
Operating Range	Universal Mains, 85-265V
Consumption / Current draw and Thermal dissipation @ 230 V	13W / -A / 78.4 BTU/h (Idle) and Thermal dissipation @ 230 V     15W / -A / ------ BTU/h (I/8 max. power@4Ω)
Protections	Over-Current, Over/Under Voltage, Output DC and Over-Temperature, Short Circuit Protection
Analog Input	1 x XLR electronically balanced, +12dB
Analog Output	1 x XLR electronically balanced (Link)
AD & DA Converters	24bit
Frequency Response (DSP)	20 Hz - 20 KHz; -0.5dBu at 20 Hz and 20 kHz

 

DSP & Processing

DSP Engine	MARANI® DSP
DSP Resolution	24bit (data) x 24 bit (coeff.),54bit accumulation registers,  96 bit precision on intermediate processing data
Parametric Equalization	3 filters on input channel LoShelving, Bell and HI-Shelving 5 filters on output channel only one selected as Bell or Shelving
Filter Type	Bell, Low/High Shelving Variable Q
Filter Gain	Input from -6dBu up to +6dBu by 0.5dBu resolution steps Output from -12dBu up to +12dBu by 0.5dBu resolution steps
Center Frequency	Selectable with 1Hz resolution step from 20Hz up to 20kHz
Bell Filter Q/BW	Q from 0.4 up to 8 by 0.1 resolution steps
Low/High Shelving Filter Q/BW	Q from 0.4 up to 5 by 0.1 resolution steps
Crossover Section HPF/LPF	Butterworth 6/12/18/24dB per octave  Bessel and Linkwitz-Riley 12/24dB per octave  Filter resolution 1Hz steps
Peak Limiter	Threshold from -18dBu up to +12dBu Release time from 25ms up to 350ms (1ms resolution up to 200ms, 5ms res. up  to 350ms) Attack time from 1ms up to 50ms(1ms resolution)
Delay	7ms for input channel and 2ms for output woofer 10.4us/Adj 1ms per channel

General

User Preset	8
Front Panel	GAIN pot. -30dBu ~ 0dBu PRESET EQ 8 Positions Rotary encoder switch Green LED (Power); Red LED (Limit) 1 x volume potentiometer 1 x XLR female connector (Input) 1 x XLR male connector (Link Output) 1 x MIC/MUSIC Switch 1 x Ground-lift toggle Switch 2 x Locking PowerCON® 20A: AC Mains (blue) - AC Link (white) On/Off Power Switch
Dimensions	362mmX179mmX80mm
Weight, Net / Shipping	6.09 lbs (2.76 Kg) / 8.83 lbs (4 Kg)